Spec Guide · CSI 26 05 33

Specifying PVC-Coated Conduit: Robroy Plasti-Bond

PVC-coated rigid conduit protects the raceway where bare steel or aluminum would corrode: treatment plants, chemical and food processing, coastal sites and buried runs. Here's what to put in your spec so the system that shows up on site is the one you designed.

CSI section26 05 33 Raceways and Boxes
SubstratesRigid steel and aluminum
Brazill coverageNYPHILLYDC

When to specify it

Use PVC-coated conduit where the environment will attack the raceway faster than the building's design life.

Water and wastewater

Headworks, digesters, chemical feed rooms and any space with corrosive gases or moisture.

Chemical and petrochemical

Process areas and hazardous locations, where coated sealing fittings and Form 8 condulets carry the protection through the whole system.

Coastal and marine

Piers, ports and salt-air exposures where galvanizing alone won't last.

Underground transitions

Direct-burial elbows and stub-ups, where PVC-coated sealing locknuts transition to coated elbows.

What sets Plasti-Bond apart

From Robroy's published Plasti-Bond materials:

  • 40 mil PVC exterior with a 2 mil urethane interior coating.
  • ETL PVC-001 verified for PVC-coated rigid conduit, based on Intertek's 200-hour adhesion test.
  • Available in steel or aluminum rigid conduit.
  • Rigid conduit UL 6 listed; hazardous-location fittings UL 1203 listed.
  • Form 8 condulets with V-Seal gaskets, rated Type 4X and IEC IP69.
  • Exceeds NEMA RN-1, the voluntary standard for PVC-coated conduit.

Codes and standards to reference

ReferenceWhat it covers
NEC Article 344Rigid metal conduit (the base raceway under the coating)
UL 6Electrical rigid metal conduit, steel
UL 514B / UL 1203Conduit fittings / hazardous-location fittings
NEMA RN-1PVC-coated rigid conduit and IMC
ETL PVC-001Intertek verification of PVC coating adhesion and performance

What to put in your spec

Robroy's own guide spec for Section 26 05 33 covers these points. Pull the full language from the manufacturer download above.

  1. Coating: PVC exterior and urethane interior, with ETL PVC-001 verification and the label on the product.
  2. Sleeves: a PVC sleeve at every female opening (except unions), sized to the conduit OD.
  3. Threads: urethane coating on all female threads; PVC-coated sealing locknuts on exposed male threads without sleeves.
  4. Fittings and supports: Form 8 condulets, coated hazardous-location fittings, and clamps and U-bolts sized for coated conduit.
  5. One manufacturer: conduit, fittings and accessories from the same manufacturer, so the coating system matches end to end.
  6. Certified installers: require a current manufacturer-certified installer card before installation starts.

Check these at submittal

Most PVC-coated failures start with a mixed system or untrained installation. Before you approve:

  • Product data shows the ETL PVC-001 verification, not just UL 6.
  • Interior coating is urethane, not bare galvanized.
  • Fittings, elbows and supports come from the same coated system.
  • Installer certification cards are submitted, not promised.
  • Hazardous-location fittings carry UL 1203.
  • Any substitution matches every item above, not only the conduit.

Want a second set of eyes on your spec?

Send us your draft section or project details. Our specifications team will review it and send back notes.

Product information is drawn from the manufacturer's published materials. Always confirm current listings and specifications with the manufacturer before issuing documents. Sources: Robroy Plasti-Bond · plastibond.com · PVC-Coated Raceway Spec Guide